4 tons of fuel boiler Product description: 4 tons of fuel oil boiler is heated by a burner, fuel atomization effect, fuel combustion, can not see the chimney smoke, so the green fuel boilers, energy efficient. After spraying fuel through the burner into the furnace in the atomized droplets, and easily mixed with air and the rapid combustion heat flash. Compared with coal-fired boiler with the same capacity, and parameters, which furnace volume heat intensity may be increased about twice. But to reduce the thermal load of the burner zone, in order to avoid overtemperature waterwall tubes in this area, so the furnace volume is only reduced by about 1/3. Because the ash content of fuel oil is small, without slagging in the convection heating surface, it allows the furnace exit gas temperatures as high as 1300 ~ 1350 ℃, and narrow a pitch between the convection heating surface to increase the flue gas velocity, thereby increasing the heat transfer coefficient of the heating surface, the heating area savings and steel. Features: 1, the boiler burner automatic combustion control in accordance with instructions, stop, separate control box has a number of security, performance, security and stability, low maintenance. 2, the inner fire tube inserted spoiler retardant, smoke slow speed, to strengthen the heat exchanger, combustion heat conducting large extent to the water, the low temperature flue gas discharged from the smoke chamber, reducing heat loss and save fuel. 3, the water level sensor water level real-time monitoring, to continuously monitor the water level is normal furnace. While controlling the temperature and replenishment level sensor solenoid valves, the boiler water may be continuously supplied. 4, centrifugal multi-layer insulation glass wool, steel for packaging famous white color, heat loss, anti-rust appearance. 5, the product is widely used in hospitals, schools, hotels, hotel, bath center and other enterprises. Boot check: 1, various instruments, whether the instrument to confirm the adequacy of fuel tank, and the inlet valve is opened. 2, confirm the soft capacity and the water tank boiler water quality meets the requirements of the main valve is opened and boiler feed water inlet valve. 3, rotation of the oil filter to remove debris. 4, drain the remaining water in the boiler, while the opening operation of the low level alarm and chain. Boiling furnace process: 1, before the new boiler furnace should be boiled to remove impurities and dirt inside the boiler, or trisodium phosphate soda cooking oven may be employed to prepare a 20% concentration was added furnace (not note the solid directly into the furnace). 2, after closing the steam valve and the water table Hancock, opening the vent valve according to the procedure stoker firing power may be low heat and temperature rise at the beginning, when there is moisture in the furnace, close the vent valve when the valve is discharged from the vent, the furnace pressure is raised to be at around 0.1MPa, the boiler should be checked for leakage and various accessories such as fittings, if any leakage should be promptly fastened. 3, when the pressure in the furnace reached 0.3MPa, the normal shutdown program shutdown, let the furnace pressure decreased to 0.1MPa or less, the drain valve open, give up all the water in the furnace. 4, opening into the hole, rinsed with soft water inside the boiler until the washing water coincides with the degree of acid-base soft water, after closing and opening into the hole Hancock water gauge. 5, after the completion of cooking stove washing, all restore normal operation, before normal operation stoker.
Group director Lu Fang fast high-level group on behalf of orphans and disabled children visited here, he said the new living environment and welfare conditions of equipment is better than the original, to see the children grow up healthy and happy in the teacher's meticulous care, heartfelt Pleased. We hope to have more caring people and companies to give them love and support, so that they get more happiness.
The main difference between the gas boiler and gas consumption for 4ton steam boiler What is the main difference between what gas boilers and gas steam boiler is? Nominally, a clear distinction between gas and steam boiler wherein the boiler fuel gas is different. The former use of natural gas, which uses coal. I think a lot of user concerns boiler is why they should cancel gas-fired boiler, because many people have purchased and used the gas boiler. If they switch to gas-fired boiler, it will be a huge expenditure. First, according to the current direction of development of the ecological environment of China, gas boilers will gradually be replaced by gas-fired boiler or other clean and green energy boilers, gradually withdraw from the stage of history. To say a big difference between the gas boiler and gas steam boilers, gas-fired boiler is mainly due to the elimination of environmental protection. From the fuel supply portion, only a gas boiler tube connected to the boiler; gas boiler needs coal field, coal (with or artificial), coal transportation, handling, storage and loading of coal boiler process. It will produce dust, causing serious pollution to the people's living environment. From the point of view of atmospheric emissions, natural gas is very small dust content, substantially negligible; high ash content of coal, the ash content of about 10-30%, the combustion smoke. If dust emission reduction facilities, emissions will increase; if more dust removal facilities, the corresponding costs will increase, this is not a long-term solution. In addition, the sulfur content of natural gas is very small, dust removal, desulfurization and denitrification can get gas boilers, gas boilers need only consider the denitrification problem. From the other point of view of waste disposal, natural gas substantially free of other contaminants, especially in city gas. In the case of coal, the coal field (especially small boilers mainly built in the open air) to produce coal slurry water during the rainy season, or sink into groundwater. When entering the surface water, the combustion ash conveyance of dust is generated. Of course, there are differences also in other ways. For small boilers, gas boilers are more energy efficient than gas boilers, equipment flow is simple, small footprint, low operating and maintenance costs, and so on. These are the main difference between the gas boiler and gas steam boilers, as well as the significance out of gas boiler. As can be seen, the use of gas-fired boiler is the trend of the whole society.
Classification accuracy of gas consumption for 4ton steam boiler and hydraulic machines with precision introduce gas steam boiler and hydraulic classification of a gas steam boiler By Type 1, an industrial gas steam boiler: heating and for industrial production and so on. Most of the parameters for the low, low capacity boilers, the fire bed combustion and thermal efficiency is relatively low. 2, power station boilers: mainly for power generation. Most high-parameter, large-capacity boiler, firebox and allow more efficient combustion. 3, the ship's boiler: a marine power. Such boilers generally low parameters, fuel oil, the requirements of small size, light weight, easy to move more. 4, locomotive boiler: The main use of locomotive power. Lower overall parameters are small capacity boilers, fire bed combustion, requires compact, movable. Two gas steam boiler in accordance with the kind of the working fluid and an output state classification can be divided into: 1, the steam boiler: the working fluid is steam outlet. 2, hot water boiler: hot water as the working fluid outlet. 3, special working fluid boiler: export of special working fluids, such as certain organic matter. Three outlet gas steam boiler in accordance with the pressure of the working medium can be divided into: 1, pressure boiler: the outlet steam pressure 14MPA (140kgf / cm). 2, high-pressure boiler: the outlet steam pressure 10MPA (100kgf / cm). 3, sub-pressure boiler: the working fluid outlet pressure of 2.5MPa. 4, pressure in the boiler: the outlet steam pressure of 3.9MPa (39kgf / cm). 5, supercritical pressure boiler: outlet steam pressure is about 25MPa (about 250kgf / cm). 6, subcritical pressure boiler: outlet steam pressure of 17MPa (170kgf / cm?). 7, low-pressure boiler: the outlet refrigerant pressure (gauge pressure) is less than or equal to 1.3MPa (13kgf / cm). Accuracy of the hydraulic machine, determines the precision of the parts. However, only static accuracy to measure the level of accuracy of press is not very accurate. This is because the size of the mechanical strength of the press itself has a great influence on the punching accuracy. If the strength of the press itself is low, the machine will be modified such that the pressure at the instant of Ao punching pressure is reached, so that, when the above-described conditions in a static tune even good, also since the strength of the deformation caused by the sample bed, differences occur. This indicates that the accuracy of the press and has a lot of strength, and the magnitude of the intensity of the work has a great influence on the press, so that high-precision parts and punched continuous strong cold stamping, the accuracy must be selected high, and the rigidity of the press.
[email protected]
