Subsequently, the delegation visited the company's boiler cleaning laboratory, technicians demonstrated to the delegation of the company's latest product boiler operation, and use of DCS control system in the laboratory trace data. Mr. Liu to our boiler products to achieve nitrogen oxide (referred to as NOx) emissions below 18 mg or less, is widely used in Beijing APEC venue, the Central Authority and other countries prefix institutions and other international occasions expressed a high degree of praise and encourage.
Classification bottom side Henan residential chips hot water boilers for sale fuel boiler fast small as we explain the use of hot water boiler fuel What are assembled into a notebook-type water tube furnace control panel, all of the action are stored on the smart chip, maintaining a furnace automation, intelligent, intelligence and personalization, to keep the Zidongkongzhi furnace temperature. This hot water boiler is the energy conversion facility, the type of kinetic energy of the furnace with a fuel chemical energy, electromagnetic energy, heat energy, etc. smoke, and after converting furnace, must be provided outside the output energy of steam, hot water or inorganic heat carrier. Gas boiler effect ignition system and fuel gas is ignited depending on the compound, the key member includes: an ignition transformer, electrical ignition stage, electric high-voltage cable fire. Compare Security Council this ignition system called electronic pulse ignition, such as natural gas is Zhuoyi energy-saving boiler manufacturers widely used. Its convenient and save time, as long as the finger can be pressed, and high safety factor, because life is not prone to production safety accidents death Xihuo arise, if the situation Xihuo appears, immediately turn off the control relay, off-gas loop . Computer processing furnace boiling hot water boiler part of the control panel, all functions are stored on the smart chip, maintaining the automated, intelligent and personalized furnace, furnace temperature to achieve a Zidongkongzhi. Automatically terminate the heating temperature is too high; the display font size to display the temperature, boiler water temperature straightforward. Exceeds the temperature was warmed automatic termination; display font sizes that vary depending on temperature, the furnace temperature simple. 2. boiler water temperature can provided 10 ℃ ~ 100 ℃. The furnace can not only produce bath with boiling water, boiling water can produce consumption, either to the furnace, but also to the furnace. 3. The top vents under the furnace wall, furnace in the non-pressure situation, the explosive risk-free, bare metal provisioning with over-temperature maintenance (inside the furnace when the temperature is high, heat pipe automatic termination of work to do, and came bee song alarm). Again when maintenance overtemperature (secondary circuit is automatically disconnected when the temperature exceeds 105 ℃ furnace shell), and less water to avoid air burning maintenance (water is less than when the furnace is very low amount of water in the secondary circuit of the furnace shell temperature exceeds 105 ℃ auto-off), when the water is less than the low water furnace automatically disconnect the secondary circuit, the furnace terminate work to do and came buzzer alarm) and other security Council safeguards. Much of this hot water boiler is converted from a hot water boiler is made early, it should belong to the ecological pot of water through the bad within the furnace. To ensure the safety and reliability of the coefficient of water circulating furnace, the furnace has to be a predetermined aspect ratio, and thus a large volume of such a heating furnace, the steel consumption and to enhance profits depend.
Measures to improve the thermal efficiency of the fuel gas-fired boiler wns type of chemical oil-fired boiler which is incomplete combustion heat loss and mechanical incomplete combustion heat loss. Because almost no ash after combustion of the gas boiler, solid and liquid fuels without mechanical incomplete combustion, there is no need to consider the mechanical incomplete combustion of the gas boiler heat loss. In all heat losses, heat losses have tremendous proportions, when the high thermal efficiency of boilers, heat losses so the total loss of the main heat losses of fuel gas-fired boiler flue gas heat loss is the exhaust gas temperature and For air excess factor. When the exhaust gas temperature decreases, high thermal efficiency can be obtained, for example, a conventional three-pass steam boiler, furnace used in the past straight and smooth smoke tube, must increase the heating surface is arranged to make the exhaust gas to an acceptable degree, the theoretical discharge around the smoke heat loss. Potshell causing significantly increased diameter, wall thickness increased, greatly increased metal consumption, thus further reducing the exhaust gas temperature should be greatly restricted. From the aspect of heat transfer is not only now consider only the heated area, the use of new technology enables heat transfer performance significantly increased, the difference between the heat transfer overcomes the disadvantages of the past performance of the boiler, so that the exhaust gas temperature decreases, the structure is more compact. Center back boiler combustion boiler is preferably small foreign structure, although the two-pass boiler, the heated area is small, but the use of the turbulator charming, the purpose of enhancing the turbulence of the flue gas, disrupt laminar flow boundary wall, reducing the thermal resistance, increasing the heat transfer coefficient, a smaller heating area to achieve the same high thermal efficiency. Lower exhaust gas temperature limit in theory, the exhaust gas temperature can be reduced to very low or even close to the ambient temperature, for maximum thermal efficiency. However, in practice, due to the reduction of the exhaust gas temperature, low temperature corrosion will cause, therefore, the exhaust gas temperature can drop too low, in order to ensure that the wall temperature is higher than the main boiler heating surface flue gas dew point temperature. Therefore, low-temperature corrosion has become a major obstacle to reduce exhaust gas temperature and improve the thermal efficiency of the boiler. Tail auxiliary heating surface increases, further reducing the exhaust gas temperature, fuel gas wns improve thermal efficiency of the boiler as the oil, gas fuel burn easily wns type gas boiler air preheater generally not disposed. The economizer means is a common energy, which can be recycled flue gas was able to effectively reduce exhaust gas temperature. Separation type condensing gas boiler is out of the main boiler heating surface, the installation of the condensing heat exchanger. In one aspect of the flue gas absorption can significantly reduce the smoke temperature, reducing heat losses, on the one hand the absorption of part of the potential condensing water vapor released, increasing the effective use of heat of the fuel. Ash cleaning, to ensure that the heating surface of the scale wns boiler thermal efficiency of the boiler, the presence of soot fouling and heat transfer resistance increases, reducing the heat transfer effect. The thermal conductivity of the scale and soot is almost of the same order of magnitude, with the increase in scale, soot, the exhaust gas temperature rapidly increases, the thermal efficiency is significantly decreased. So, keep the boiler heating surface inside and outside clean, efficient heat transfer, thermal efficiency and to ensure the safe and economic operation of boilers, boiler fuel gas-fired boiler ash cleaning is required.
The main reason gas steam boiler produces smoke which fuel gas steam boiler main cause of smoke. A fuel gas steam boiler: oil, gas oil quality is not good when the gas contains more water, reduce the heat value of the fuel, while producing steam, the furnace temperature tends to decrease, making it difficult to burn, easy to produce smoke. Water and more oil, mainly when unloading rain water into the oil during heating the oil in water vapor penetration. When the oil contains impurities, the impurities unburned produce fine coke, the coke into fine smoke, dust becomes large, and the formation of soot. Impurities contained in the oil and gas, but also affect the pure oil and pure combustion gas generated soot. Oil impurities, mainly due to inappropriate choice of filters or filter difference impurity removal effect. Second, the failure of the fuel atomizing nozzle member main burner fuel oil atomizing nozzle. Atomizing oil burner nozzle fails, affecting the quality of the atomization, easy to poor combustion. 1, the adhesiveness between the bonding surface of the oil and the consequences of failure oil atomizers swirl atomizers and the splitter plate well, leakage will occur, atomized large oil particles, increasing the amount of fuel injection and the like. In this case serious deterioration of the quality of the combustion, the oil droplets have landed on the water wall, stacking up oil coke, partially unburned black smoke into droplets. The tangential swirl chip groove clogging mist causes uneven density distribution in the dense side of the oil mist, combustion air be insufficient. In the more dilute side of the oil mist, combustion air causes severe local excess. Mixed with oil, wind conditions deteriorated significantly, combustion conditions deteriorate, resulting in black smoke. 2, spray atomization slice failure and the consequences of failure to clogging and wear. Nozzle clogging, resulting in blockage of the fuel injection quantity is not glib increase, oil particle size thicker, the effect of fuel poor and black smoke. Wear injection port, a large hole diameter, increasing the amount of fuel injection, increasing the particle size of oil affect combustion efficiency, produce black smoke. The use of artificial gas burner, naphthalene and tar and other impurities will block the nozzles, the influence of gas distribution, resulting in black smoke. Should therefore be cleaned regularly, or clogging of the selected burner. 3, the partition partitioning poor poor, insufficient supply of air into and excess. The amount of air can not meet the requirements of the fuel combustion, so that combustion of fuel can not be sufficiently black smoke. The amount of air, will result in lower combustion temperature, black smoke and fuel difficult to burn. 4, the furnace temperature is too low when starting the furnace, fuel oil steam boiler furnace temperature is too low due to easy black smoke. 5, the furnace hearth product oil is sometimes caused by internal combustion nozzle oil accumulated inside the chamber, the oil reservoir coke black smoke at high temperature. Causes dripping of fuel combustion nozzle: ① The drip just work, just at the operating pressure is too low, the oil will flow from the nozzle, instead of the discharge. The reason for low oil pressure is a solenoid valve, the valve is clogged filter or the like or failure caused by contamination. ② In the dripping process work, probably because the relative position of burner nozzle mounting head too far, improper ignition electrode position, the oil into the atomizer, the nozzle holder is mounted is not tight, nozzle dirty, low oil pressure caused. ③ When the dripping stopped, because the line between the pump and the air nozzle, electromagnetic valve or a hydraulic valve or dirty failure. 6, the furnace flue purged countless consequences when the furnace flue remnants of oil and gas, when gas purging endless, high temperatures encountered in the explosion and black smoke. 7, the furnace smoke, sparks, the furnace pressure is too ①; ② inappropriate choice of the burner, the burner flame is too long or too much power; ③ improper combustion ratio, there are more to produce products of incomplete combustion; ④ atomization quality is not good nozzle or improper installation location, or affect the combustion flame into the furnace off port; ⑤ flue is blocked, poor smoke; ⑥ a secondary air mismatches; irrational ⑦ furnace structure; ⑧ oil spray angle is selected from with improper.
[email protected]